基本释义:

腐蚀涂料

网络释义

1)etching ground,腐蚀涂料

2)anticorrosive coating,防腐蚀涂料

3)anti-corrosive coatings,防腐蚀涂料

4)anticorrosion coatings,防腐蚀涂料

5)corrosion protective coatings,防腐蚀涂料

6)anticorrosive paint,防腐蚀涂料

7)Anticorrosion coating,耐腐蚀涂料

8)anticorrosive coatings,防腐蚀涂料

9)self-etching primer,自腐蚀涂料

10)Heavy duty coating,重防腐蚀涂料

用法和例句

Current status and developing trends of binders used in waterborne metal anticorrosive coatings;

水性金属防腐蚀涂料所用基料现状及发展

The key to the performance of anticorrosive coating was the kind of fillings and dosage.

合理地选择颜填料的种类及其含量是决定防腐蚀涂料耐腐蚀性能的关键。

The development tendency and research hotspot of five coatings such as anticorrosive coatings, coil coatings, functional coatings, green wood coatings and powder coatings in future were introduced.

综述了目前中国涂料业的发展概况,并介绍了今后发展趋势和研究热点──防腐蚀涂料、卷材涂料、功能涂料、绿色木器涂料和粉末涂料等5种涂料。

Aiming at the corrosion circumstances of downhole oil tubes and the needs of anti-corrosive coatings,YG series of anti-corrosive coatings for oil tubes are developed,in terms of YG-01 baking anti-corrosive coatings for oil tubes,YG-03 air-drying anti-corrosive coatings for oil tubes and et al.

针对井下油管的腐蚀环境和防腐蚀涂覆的需要,研制了YG系列油管防腐蚀涂料,包括YG-01烘烤固化型油管涂料和YG-03常温固化型油管涂料等。

The present situation of anti-corrosive coatings in China is introduced.

介绍了我国防腐蚀涂料工艺的现状,指出了目前我国重防腐涂料工业存在的问题及防腐蚀涂料的最新研究动态,详细分析了其发展趋势。

anticorrosion coatings, coil coatings, functional coatings, powder coatings a.

在"十一五"期间,中国涂料行业主要关注的5大热点课题是防腐蚀涂料、卷材涂料、功能性涂料、粉末涂料和水性木器涂料。

High chlorinated polyethylene, replacing chlorinatedrubber, and modified resin as main film former are used toprepare anticorrosion coatings of good performance, reducingthe cost of production and promoting the use of newtechnology.

以HCPE和改性树脂为主要成膜物质,制备性能优良的防腐蚀涂料,降低生产成本,促进新技术应用。

A water-borne epoxy was synthesized by emulsion of vinyl-monomers and epoxy resin, which can be used to prepare anticorrosion coatings with comparable properties to solvent-based ones.

采用乙烯基单体与环氧树脂乳液共聚,得到了水性环氧树脂,所配制的防腐蚀涂料性能达到溶剂型环氧树脂涂料水平。

This article has described the applications of waterborne accylic emulsion,waterborne alkyd emulsion and waterborne 2K epoxy in waterborne corrosion protective coatings,and compared their properties of salt spray resistance and heat and humidity resistance.

简述了水性丙烯酸乳液、水性醇酸乳液和水性双组分环氧树脂在水性防腐蚀涂料中的应用,并进行了耐湿热性能和耐盐雾性能的比较。

A PC(polyester epoxy) modified HCPE(high chloropolyethylene) corrosion protective coatings by blending of PC and HCPE has been developed, which could be used as an alternative of chlorosulphonated polyethylene(CSM) corrosion protective coatings.

采用酯化型环氧树脂（ＰＣ）与高氯聚乙烯（ＨＣＰＥ）共混，制得ＰＣ改性ＨＣＰＥ防腐蚀涂料，可作为氯磺化聚乙烯（ＣＳＭ）防腐蚀涂料的替代品种。

The composition of the HC solar energy shielding corrosion protective coatings was described.

叙述了HC太阳能屏蔽防腐蚀涂料的基本组成。

Formulation design of anticorrosive paint and raw metarial selection;

防腐蚀涂料配方设计要点及原料选用原则

Epoxy - polyurethane IPN anticorrosive paint forms film with excellent anticorrosive property and adhesion.

研制的环氧-聚氨酯互穿网络(IPN)防腐蚀涂料具有优异的防腐蚀性能和附着力。

Based on epoxy diacrylate and fural amine/epoxy IPN as binder, an anticorrosive paint with excellent heat and impact resistance is developed.

以环氧丙烯酸酯与呋喃胺/环氧树脂的互穿聚合物网络(IPN)为基料,制备了耐温、抗冲击性能优良的防腐蚀涂料。