基本释义:

挠度,弯度

网络释义

1)deflection,挠度;弯度

2)bending deflection,压弯挠度

3)bending deflection,弯曲挠度

4)reverse bending deflection,反弯挠度

5)flexure,弯曲，挠曲;弯度;挠度

6)large deflection,大挠度弯曲

用法和例句

Design of structural parameters and bending deflection of straightening machine for conducting bar

电铜导电棒矫直机结构参数及矫直压弯挠度设计

It is difficult to get a proper practical answer of bending deflection for H-Beam roller straightening.

H型钢辊式矫直压弯挠度的计算一直难于得出适用工程的解。

In order to avoid flaws in the process of H-beam straightening, an adequate mechanical model was established and the relations between bending moments, forces and bending deflections of the H-beam in nine-roller straightening were deduced.

为了避免矫直过程中出现矫直缺陷,通过建立适当的矫直力学模型,求出了H型钢九辊矫直的压弯挠度与弯矩、矫直力的解析关系,确定了生产中调节矫直辊压弯挠度来保证各辊处的弯矩、矫直力等力能参数的范围。

On the basis of the mathematical elastic theory, the bending deflection expression of the complex Fourier Series is derived at first for the infinite plate with a unit circle.

　应用弹性力学的复变函数理论,首先导出了圆孔无限大板弯曲挠度的复Fourier级数表达式,再把孔的边界条件进行复Fourier级数展开,用待定系数法确定级数的未知系数。

The deformation curve of the plate is simulated by means of curve fitting,with the relationship between the intermesh and the reverse bending deflection obtained.

针对某辊式板带矫直机的结构特点,采用大变形法则确定了压下量,并利用曲线拟合方法,模拟矫直时带钢的变形曲线,确定了压下量与反弯挠度的关系。

In this paper a new analytic solution to large deflection of stiffened plates is presented.

提出了一种加筋板大挠度弯曲的新解法 ,此方法将离散的梁与板结合起来建立一个统一的控制方程。

In this paper, the modified method of multiple scales is applied to study the bending problems for circular thin plate with large deflection under the hinged and simply supported edge conditions.

本文应用修正多重尺度法研究圆板在铰链和简单支承条件下的大挠度弯曲·作出其级数解，分析其边界层效应和证明其渐近性

Design of structural parameters and bending deflection of straightening machine for conducting bar

电铜导电棒矫直机结构参数及矫直压弯挠度设计

bending stiffness

抗挠劲度,抗弯硬挺度

steep-S flexible riser

高弯度S形挠性立管

A DYNAMIC BENDING MODEL FOR LARGE DEFLECTION OF INCOMPRESSIBLE SATURATED ORTHOTROPIC POROELASTIC PLATES

饱和不可压正交各向异性多孔弹性大挠度板的动力弯曲模型

determination of flexural stiffness of fabrics:flexometer method

织物弯曲硬挺度的测定法: 挠度计法

Solution to the Large Deflection Problem of Thin Plates by BEM Method

用边界元法求解薄板大挠度弯曲问题

Effect of Entrance/exit Leveler Roller' intermesh to Plate Flatness

辊式矫直过程中板带弯曲挠度的确定

STUDY ON LITTLE DEFLECTION IN MEASUREMENT OF FLEXURE STRENGTH FOR SILICON WAFER

硅片抗弯强度测试方法中小挠度问题研究

Find the value of the bending stress and the deflection at the center if the ribs are omitted.

如果略去肋条，求中心处的弯曲应力和挠度之值。

Analysis and Calculation of Deflection for Reinforced Concrete Flexural Members Strengthened by FRP Sheet;

外贴FRP布钢筋混凝土受弯构件挠度计算分析

A System of New Boundary Integral Equations of Thin Plate Bending;

薄板小挠度弯曲问题的新的边界积分方程

DEFLECTION FOR REFLECTOR PLATE OF HELIOSTAT BASED ON THIN PLATE FLEXURE THEORY

定日镜反射板基于薄板弯曲理论的挠度分析

Bending deflection properties of bamboo particle-wood fiber plywood.

竹碎料-木纤维复合板弯曲挠度特性的研究

The Research on Deflection Control of Concrete Beam Reinforced with New-type BFRP Bars

新型BFRP筋增强混凝土受弯构件挠度控制

The slip displacement increases the curvature, reduces the stiffness, increases the additional moment and consequently leads the increase of deflection.

滑移增大结构曲率,降低构件刚度,增加附加弯矩,从而引起挠度增大。

Strength Criteria in Semi-Analytical,Large Deflection Analysis of Stiffened Plates in Local and Global Bending

局部和整体弯曲下加劲板半解析大挠度分析中的强度标准

Computer Simulation and Analysis of Temperature Fields and Flexibility Compensation of Calender Rolls;

压延辊筒温度场及挠度补偿计算机模拟分析

In the analysis of plates in bending, deflection is obtained by solving Eq.

在受弯板的分析中，借求解满足板边界处条件的方程得出挠度。