基本释义:

设计注释

网络释义

1)design note,设计注释

2)design of sustained release,缓释设计

3)injection design,注塑设计

4)grouting design,注浆设计

5)injection mold design,注射模设计

6)grouting borehole design,注浆孔设计

用法和例句

Detailed introduction is made from grouting design,calculation,construction method,matters deserving attention in construction,quality inspection and other aspects.

结合工程概况,提出采用渗透式注浆方式作为加固防护方案,对其注浆设计计算过程、施工工艺、施工注意事项、质量检查等方面进行了介绍,并对其施工效果进行了评价,以供类似工程参考借鉴。

The paper also briefiy introducd drilling and grouting design.

介绍采用地面打钻深孔注浆充填主、副井井壁后空硐,应用了深孔位防偏斜技术,深孔位套管技术等多顶新工艺、新技术,通过浆液高压挤压作用降低孔隙率,减少地层压缩,加固地层,防止井筒的突然破坏,文中对钻孔灌注浆设计进行重点介绍。

This paper introduced the ground pre-grouting design and the key technical measures of construction through an engineering practice, and summarized some useful experiences.

本文通过实例介绍了地面预注浆设计和施工关键技术措施,总结了提高注浆效率、改进“三同时”建井工艺的有益经验。

The liquid silica rubber(LSR) had unique physical performance,through the liquid silica rubber injection mold design example,analyzed several attention points in designing injection mold.

液体硅橡胶(LSR)具有独特的物理性能,通过液体硅橡胶注射模设计实例,分析了其注射模设计中应注意的几个问题。

In this article, the process of injection mold design using SolidWorks software were introduced.

主要介绍了用Solidworks软件进行注射模设计的一般步骤,并且结合鼠标外壳注射模设计的具体实例,介绍了利用Solidworks进行注射模设计的基本方法。

Taking injection mold design and mold cavity NC machining of the plastic shell as an example, stated the technology and step of mold designing and NC machining using CAD/CAM software in details.

以一塑料外壳注射模的设计和模具型腔的数控加工为例,较为详尽地讲述了运用CAD/CAM软件进行注射模设计和数控加工的工艺和步骤。

Design of Injection Mold with Auto-Stripping Inner and Outer Screw Mechanism By Oil Cylind

油缸式自动内外螺纹脱模注射模设计

Cellular Phone Outer Shell Injects the Mold Design and Application of CAD/CAE/CAM;

手机外壳注射模设计与CAD/CAE/CAM的应用

Design of Injection Mold for the Upper Clutch Coupling

基于CAE分析的上离合器注射模设计

Design of auto-stripping injection mould with parting-out in sequence and pin gate mechanism

顺序分型点浇口自动脱料注射模设计

Application of CAD/CAE Technology to Injection Mould Design

CAD/CAE技术在注射模设计中的应用

DESIGN OF INJECTION MOLD FOR THE AUTOMOBILE CONTROL PANEL FOR THE LEFT FRONT SWITCH

汽车左前开关控制面板的注射模设计

Design of Injection Mold of the Tee Pipe Based on Pro/E

基于Pro/E的三通管注射模设计

Design of Injection Mold for the HOLDER-GEL Part in CD Writer

刻录机中HOLDER-GEL零件的注射模设计

Design of Injection Mold to Magnetic Treat Instrument Based on CAE Technology

基于CAE技术的磁疗仪注射模设计

Design of the Injection Mould for Box Cover of Combined Switch Based on Pro/E

基于Pro/E的组合开关盒盖注射模设计

CAE-based design of injection mould for casing cover of hair dryer

基于CAE分析的风筒壳后盖注射模设计

Molding Process Analysis and Injection Mold Design for the Automobile Door Plate

汽车门板零件工艺分析和注射模设计

Pro/E based design of injection mold for T-Joint fittings

基于Pro/E三通管件注射模设计

Optimization of feed system and design of injection mould for automotive engine cover

汽车发动机罩盖浇注系统优化与注射模设计

Application of failure mode effects analysis in design of injection mould;

失效模式及后果分析在注射模设计中的应用

The injection molding of LCD shell and push button key in a mould

显示器壳体与按键同模成型注射模设计

UG/NX-based design of injection mould and mould flow analysis

基于UG/NX的洗发水瓶盖注射模设计与模流分析

The Model Stream Analyses a Software Injecting Model Application in Designing that in Monoblock

模流分析软件在壳体注射模设计中的应用