基本释义:

压缩模制

网络释义

1)compression molding,压缩模制

2)compressed pattern lumber,压缩制模木材

3)compressive modulus,压缩模量

4)compression modulus,压缩模量

5)compressibility modulus,压缩模量

6)compression molding,压缩模塑

用法和例句

Calculation of compressive modulus of grid structure -composite foundation;

格栅状复合地基压缩模量的计算

Value determination problem of compressive modulus E_s of soil layers ⑦,⑧ and ⑨ in Shanghai soft soil foundation;

论上海软土地基⑦⑧⑨层压缩模量E_s的定值问题

It was found that gelatin coatings were formed on the pore walls of porous scaffold samples successfully without destroying their porous characteristic,but these coatings improved the compressive strength and compressive modulus o.

复合明胶涂层提高了样品的压缩强度和压缩模量,与未涂覆样品相比,涂敷样品受压时的应变特性发生了明显变化。

Test research on compression modulus of sandy soil tunnel surrounding rock;

砂类土体隧道围岩压缩模量的试验研究

The response to electric field of the composite systems was studied by measure of compression modulus of the elastomers and dynamic-exam of resistance in the cure .

通过对弹性胶体压缩模量的测试和胶凝过程中电阻的动态监测,研究了胶体体系对电场的响应行为。

The compressibility modulus of the dewatering subsidence,sE,is mainly determined by the character diameter of the sand,20D,and the ef.

疏水沉降的侧限压缩模量sE受特征粒径20D和水压降hD控制,20D,hD越大,sE越大;当土样不变时,sE与hD呈正相关关系;当hD一定时,土体的细颗粒含量越多,20D越小,则侧限压缩模量sE越小,土体变形量越大。

Based on settlement data measured in field,compressibility modulus and consolidation coefficient of soil layers are obtained by back analysis method.

基于沉降实测资料,采用反分析方法,确定了各土层的压缩模量和固结系数,并将反演得到的参数代入太沙基一维固结方程,对后续沉降进行预测,从而确定分级压载的下一级压载时间与压载量。

The compression molding process of such long fiber reinforced PP was investigated.

　采用粉末浸渍的方法制备连续玻璃纤维增强聚丙烯预浸料,经切割获得长纤维增强聚丙烯粒子,采用单螺杆挤出机挤出形成模塑料,探索了模塑料的压缩模塑成型工艺,研究了成型后材料的力学性能及其影响因素。

A mathematical model of heattransfer in partwas established to simulate thermalbehav- ior of GMT parts during compression molding,coupled with non- isothermal crystallization kinetics of polypropylene.

采用有限元方法 ,对 PP/ GMT制品压缩模塑的冷却与结晶过程进行数值模拟 ,采用非等温结晶模型 ,计算出不同条件下制品中树脂的结晶度和制品内部温度分布 ,并与实验结果进行了对比 ,为压缩模塑中保压冷却时间的确定提供了理论依

The effect of matrix resin,architecture and property of reinforcement,blank design,mold temperature and blank preheat temperature on the fiber distribution during compression molding of glass mat reinforced polypropylene(GMT-PP)was investigated by measuring the fiber content in various areas of GMT-PP after squeezing flow.

通过测定玻璃纤维毡增强聚丙烯经挤压流动后不同区域的纤维含量 ,研究了基体树脂、增强材料的结构与性质、坯料设计、模具温度及坯料的预热温度等对玻璃纤维毡增强聚丙烯在压缩模塑流动过程中纤维分布的影响。

These two parameters are nowadays called the modulus of compressibility.

这两种参数现被称为压缩模量。

Determining Compression Modulus of Soft Soil by Cone Penetration Test

应用双桥静力触探确定淤泥压缩模量

Finite Element Modeling Analysis of Compressive Modulus About X-cor Sandwich

X-cor夹层结构压缩模量有限元分析

Dynamic Evolution Pattern of Compression Modulus of Soft Clay

外荷载作用下软土压缩模量动态演化规律

Determination Method for Modulus of Compression of Sandy Soil for Yangtse River Bridge Foundation of Taizhou

泰州长江大桥地基砂性土压缩模量确定方法

EXPERIMENTAL RESEARCH ON ELASTIC RESISTANT COEFFICIENT,DEFORMATION AND COMPRESSIVE MODULI OF SURROUNDING ROCK IN LARGE-SECTION LOESS TUNNEL

大断面黄土隧道围岩弹性抗力系数、变形模量与压缩模量试验研究

Plastics--Determination of compressive elastic modulus

GB/T14694-1993塑料压缩弹性模量的测定

Pressed together or into less volume or space.

压缩的压紧或压缩使数量或体积减少

The Numerical Optimization of the Stators in Centrifugal Compressor Model Stage with Small Flow Coefficient;

离心压缩机小流量模型级静止元件的数值优化

Flow Analysis and Optimization of the Centrifugal Model Stage with Small Flow Coefficient;

离心压缩机小流量模型级的流动分析与优化

The compressing models and methods for map vector data by wavelet theory;

基于小波的矢量地图数据压缩模型和方法

Research on Video Compressed and Traffic Model in Wireless Multimedia Network

无线多媒体网络视频压缩与流量模型的研究

Methods of Geometrical Image Compression Based on Vector Mode of Images

基于图形矢量模式的图像几何信息压缩方法

The H - Squeezed Effects of K - th Power Under the Dual Mode Squeezed Vacuum State;

双模压缩真空态的K次方H压缩效应

Comparison of HMA Dynamic Moduli between Indirect Tension and Uniaxial Compression Test Modes

间接拉伸与单轴压缩模式沥青混合料动态模量比较分析

The compressive modulus of Elasticity of the butakon rubber gasket are given, based on the cotnpressive test Value of this type gasket, with the analysis and inference method by the authors.

笔者以垫片的压缩试验数据为基础，用分析推理的方法，确定出了丁腈橡胶垫片的压缩弹性模量。

explosive flux compression technique

爆炸磁通量压缩技术

full circle expanding hydraulic form

全圆形液压伸缩式模板