基本释义:

检核尺

网络释义

1)control rule,检核尺

2)check of dimensions,尺寸校核，尺寸检查

3)scale,cull,检尺

4)check,检核

5)checking,检核

6)nugget size,熔核尺寸

用法和例句

Determination of Ningxia Quasi-Geoid and Its check;

宁夏区大地水准面精化建立及检核的探讨

Like this, it can check the mistake and increase its precision of closed traverse`s measure.

这样 ,可以检核闭合导线测量的粗差和提高它的精度。

Some Checking Measures in Construction and Setting-out;

谈施工放样的几种检核措施

Then it presents the methods of surveying,adjustment,checking as well as the results of precision.

简析深圳抽水蓄能电站二等施工控制网的建立概况、测量方法、平差计算方法、检核方法、精度情况等并探讨经验。

According to methods and accuracy requirements of checking starting point data of GPS control network by current specifications and regulations, this paper analyses the checking methods and effect and discusses the methods for selecting starting point.

本文根据现行规范、规程检核GPS测量控制网起算数据的方法和精度要求,分析了检核方法和效果,探讨了选用起算点的方法。

Regression model between nugget size and processing parameters;

熔核尺寸与点焊工艺参数的回归模型

After transforming the spot welding DRC(Dynamic Resistance Curve)of stainless steel 1Cr18Ni9Ti by FFT(Fast Fourier Transform),the spectrum characteristics are analyzed and the nugget sizes of six spot welds are measured and contrasted.

1Hz处的幅频值随熔核尺寸变化的曲线斜率较小,0Hz处的幅频值随熔核尺寸的变化更为敏感。

Aiming at the localization of traditional quality detection method during resistance spot welding, a new method is set up to detect the nugget size in real time.

本文针对传统点焊质量检验方法的局限性,提出了一种实时检测点焊熔核尺寸的新方法。

The Influence of the Non Standard Timber Scaling to Tax Tee and Price;

非标准检尺对木材税费及价格的影响

Measurement of Key Dimensions of Large-size and Thin-wall Pieces Based on Vision Inspection Technology;

大尺寸薄壁零件关键尺寸的视觉检测

micrometer for checking or measuring

检查或测量用千分尺

method of inspection for dimension of refractory brick

耐火砖尺寸检测方法

film censorship survey

电影检查尺度民意调查

A Method for Accuracy Test and Repair of Big-size Square Rulers;

一种大尺寸直角尺的精度检测与修复方法

Research of visual measuring technical and application of crankshaft forging dimensions measuring

视觉检测技术在曲轴锻件尺寸检测中的应用

Inspection machining dimension of propeller shaft( intermediate shaft or counter shaft).

螺旋桨轴（间轴）加工尺寸检查。

Straight-sided spline-Dimensions tolerances and verification

GB/T1144-1987矩形花键尺寸、公差和检验

Method of inspection for last sizes

GB/T3294-1998鞋楦尺寸检测方法

Check Paper Size

检查纸尺寸与设定是否符合

Verify that the correct dipstick is being use

验证使用了正确的润滑油检视尺。

Accurate Edge Detection Based on Multisolution Analysis

多尺度分析用于图像边缘的精确检测

Research of Laser Small-scale Distorted Wavefront Measurement and Control;

激光小尺度畸变波前检测与控制研究

Sub-millimeter Tests of the Newtonian Gravitational Inverse-Square Law;

亚毫米尺度下牛顿反平方定律的检验

Planar Inspect System Base on CCD Image;

基于CCD图像处理的二维尺寸检测系统

Matched Wavelet Detection and Multiscale Geometry Analysis in Image;

匹配小波检测及图像多尺度几何分析

General Detection System of Dimension Parameter Based on CCD;

基于CCD的尺寸参量通用检测系统