基本释义:

头颅夹接头

网络释义

1)skull clamp adaptor,头颅夹接头

2)skull clamp,头颅夹

3)skull clamp pin,头颅夹针

4)connection clamp,接头线夹

5)joint bar,接头夹板

6)single-grip terminal,单夹接头

用法和例句

Through discussing the existing problems in traditional terminal anchoring and connection clamps of GLCN250 and LBGLJ185, proposes the improving measures by means of reducing the wedge coning, processing inner threads inside the wedge and widening the opening of the hollow wedge.

通过对传统使用的GLCN250接触线终锚线夹及接头线夹、LBGLJ185终锚线夹及接头线夹存在问题的探讨,对终锚线夹提出了减小楔子的锥度,在楔子内表面加工内螺纹,加宽空心楔子开槽宽度等改进措施。

The effect of bolt torque on stresses in rail, joint bars and track bolts in a rail joint is analyzed.

利用有限元软件ANSYS建立了钢轨接头的三维计算模型,分析了螺栓转矩变化对接头区钢轨应力、接头夹板应力和螺栓应力的影响。

Fish plates for light rails

GB/T11265-1989轻轨用接头夹板

Study on Hot Rolling and Heat Treatment of 56Nb Fishplate;

56Nb钢铁道接头夹板热轧及热处理工艺制度研究

Electronics appliances spring coil switch, IC transit, deal with contact, thebellows, fuse clip,slice, bearings, set tube.

电子或电器弹簧开关、IC导板、接头、风箱、保险丝夹、滑片、轴承、套管。

drill chuck with thread adapter

螺纹联接扳手钻夹头

INSTRUMENT PANEL 22-WAY CONNECTOR

仪表板２２－路接头

connection strip, electric, ceramic, not fitted with their terminals

陶瓷电线接头条板,未接接头

Direct design of FPSO based on honeycomb sandwich panel

基于蜂窝式夹层板PFSO结构直接设计

INSTRUMENT PANEL 10-WAY CONNECTOR (AT BCM)

仪表板１０－路接头（在ＢＣＭ）

connection strip, electrical, of plastic insulating material, not fitted with their terminals

电线接头条板,塑料绝缘材料制,未接接头

No rails or headboards that can trap a small head.

不要装设可能夹住小脑袋的栏杆或床头板。

Effects of Clamps on Welding Distortion in Thin Aluminum Alloy Plate

夹具约束对铝合金薄板焊接变形的影响

Experimental Study on Bearing Capacity of Bolted Steel-Wood-Steel Connections in Timber Structures

木材-钢夹板螺栓连接的承载能力试验研究

Toughness Evaluation for Welds of Thick Steel Plate with Crack Tip Opening Displacement;

厚钢板焊接接头韧度CTOD评定研究

Analysis of Static Strength for Overlap Joint Plates and Others;

搭接焊接头搭板的静强度分析及其它

connection strip, electrical, of plastic insulating material, not fittd with their terminals

电线接头条板,塑料绝缘材料制,未装接头

Plug the in-vehicle temperature sensor wire harness connector into the instrument panel wire harness.

插车内温度感知器线束接头进仪表板线束接头。

The strip goes further after croping through next pinch rolls and stops waiting for welding.

带钢齐头剪切后经夹送辊送至焊机等待焊接。

The contact area between clamp and terminal is either silver or copper.

夹头和电极之间的接触面是银的或铜的。