基本释义:

有限壁厚型的

网络释义

1)finite-thickness type,有限壁厚型的

2)effective thickness,有效壁厚

3)parison wall thickness,型坯壁厚

4)cavity wall thickness,型腔壁厚

5)Grand Thick-Walled Vessel,大型厚壁

6)section bar wall thickness,型材壁厚

用法和例句

By the way of improving roller dimensions, roller number, outer roller path diameter ,stop groove diameter and the effective thickness ,the using reliability of the bearing is advanced.

通过对轴承结构中的滚子尺寸、滚子数量、外圈滚道直径、止动槽直径公差及有效壁厚的改进,提高其使用的可靠性。

This article discusses the analysis of the joint punching shear of grouted offshore jacket leg and pile with the effective thickness of grouted element and presents three different methods to calculate the effective thickness of it with SACS program.

借助SACS程序提供了三种导管架灌浆腿柱的有效壁厚计算方法,举例对采用有效壁厚及仅采用导管架的管壁厚对管节点进行冲剪应力计算对比,结果表明采用有效壁厚计算冲剪应力对优化导管架的设计,降低工程造价是完全可能的。

On-line measurement technology of parison wall thickness for extrusion blow molding;

挤出吹塑中型坯壁厚的在线智能检测技术

A calculating formula of the relationship between beam gap and parison wall thickness is presented.

重新推导出该间隔与型坯壁厚之间的计算公式。

With the injection mold structures of female mold on stationary mold and on moving molds,the force on the female mold and male mold are different,the calculation formula of mold cavity wall thickness are also different.

凹模安装在定模上、凸模安装在动模上的注塑模结构,其凹凸模的受力情况与凹模安装在动模上、凸模安装在定模上不同,因此注塑模型腔壁厚的计算公式也不同。

On Cause and Prevention of Welding Cracks of Grand Thick-Walled Vessel in Severe Winter;

严冬施焊大型厚壁容器的裂纹成因及对策研究

Study on Design and Optimization Techniques of Parison Thickness for Extrusion Blow Molding

中空挤出吹塑型坯壁厚设计与优化技术研究

Cooling time dominates cycle time in thick-wall moulding like preform moulding.

属厚壁注塑的瓶坯，冷却时间支配着周期时间。

The Numerical Model of Original Shell in Grooved-Mold;

沟槽内壁结晶器初生坯壳的数学模型

Bottle weight, which is the same as preform weight, is essentially non-adjustable.

瓶子的重量(壁厚)相当于瓶坯的重量，而后者基本上不能调整。

Numerical Simulation of Temperature Field and Stress Field for and Axial Crack Analysis of Heavy-wall Centrifugally Cast Hollow Bloom

厚壁离心管坯温度场和热应力场的数值模拟及其轴向裂纹分析

Discussion about Calculating Mode of Solidifying-skull's Thickness in Jinan Steel's Slab CCM

济钢板坯铸机凝固壳厚度计算模型的探讨

FE Simulating and Technics for Forming of Large Thick Cylinder;

大型厚壁筒体成形工艺及有限元模拟

Finite Element Simulation Analysis of Welded Tube Forming with Small Diameter and Thickness

小直径厚壁焊管成型有限元仿真分析

Study and Application on the Cast Material of Crack Resistance Gypsum Mould and Equal Wall Thickness of Cast Mould

抗裂石膏型铸造材料及铸型等壁厚研究与应用

Fuzzy optimal design facing cavity wall thickness of large-scale die casting mold

面向大型压铸模型腔壁厚的模糊优化设计

Steps were made on the female die surface to make up for the thickness different of the blanks.

凹模表面和型腔加工了台阶以补偿坯料的厚度差值。

Nailing experimental calibration for solidification calculation model of plate slab caster in tangshan plate Co.,Ltd.

唐山中厚板板坯铸机凝固计算模型的射钉实验校验

Study on Simulation of Level Fluctuation in Wide and Thick Slab Continuous Casting Mould with Argon Blowing

吹氩宽厚板坯连铸结晶器内液面波动行为的水模型研究

Measurement of the Solidified Shell Thickness in the Secondary Cooling Zone of Continuous Casting of Bloom

大方坯连铸二冷区凝固坯壳厚度测试

Experimental Study and Theoretical Analysis on Load Carrying Apacity of Cold-Formed Flexural Members with Thicknesses Less Than 2mm;

壁厚小于2mm冷弯薄壁型钢受弯构件承载力试验研究及理论分析

Experimental study on behavior of cold-formed steel flexural members with thickness less than 2mm

壁厚2mm以下冷弯薄壁型钢受弯构件性能试验研究

Sclerenchyma cells are a more common type of supporting cell.

厚壁组织细胞是一种常见的支持细胞类型。

Thick wall model simulation of EDM spark locations detection

电火花加工放电位置检测厚壁模型的仿真