基本释义:

渣壳(焊后焊缝表面上固态熔渣)

网络释义

1)solidified slag,渣壳(焊后焊缝表面上固态熔渣)

2)welding slag,焊接熔渣

3)slackness welding,熔渣焊

4)Electroslag welding metal,电渣焊缝

5)consumable nozzle electroslag welding,熔嘴电渣焊

6)consumable guide electroslag welding,熔嘴电焊渣

用法和例句

Correlation between welding slag and usability quality of stainless steel electrode;

不锈钢焊条焊接熔渣及与焊条工艺质量的关系

The electroslay welds were found to have a lower level of fracture toughness than implied from qualification tests.

人们发现电渣焊缝的断裂韧性较鉴定试验所给的结果要低。

Application of Electro Slag Welding with Consumable Nozzle in the Vertical Welding of Blast Furnace Shell in Laigang

熔嘴电渣焊在莱钢高炉炉壳立缝焊接中的应用

Close examination of the plug welds showed the existence of herringbone patterns near the slag and voids in welds.

对塞焊焊缝的详细检查表明在焊渣及气孔附近，焊缝中存在着人字型裂纹。

Longitudinal electric resistance welded steel tubes

GB/T13793-1992直缝电焊钢管

Arc strikes outside of the welds were avoided.

焊缝外要避免电弧穿刺。

Any severe deficiency of welding seams surface like cracks, pores, slags is forbidden.

焊缝表面不得有裂纹,气孔,夹渣等严重缺陷.

The box corner welds were made with E70 electrodes.

箱型梁内角部焊缝所用的电焊条为E70。

Automatical EB Welding of Curved Weldment

工件平面曲线焊缝的电子束自动焊接

Application of the electrogas welding for the blast furnace jacket

气电立焊在高炉炉壳立缝焊接的应用

Fundamental study on hybrid laser beam and resistance seam welding (LB-RSW)

激光束—电阻缝焊(LB-RSW)复合焊接研究

The study of the control circuit of type ZDH-36 electric dreg pressure welder;

ZDH-36型电渣压力焊机控制电路的研究

Research on Welding Seam Formation Characteristics of Manual Arc Welding and CO_2 Gas Protection Welding

手工电弧焊与CO_2气体保护焊焊缝成形特征研究

Influence Factors of the Welding Quality of Electroslag Pressure Welding for Three Grade Steel Bar

三级钢筋电渣压力焊焊接品质的影响因素

APPLICATION OF CONSUMABLE GUIDE ELECTROSLAG WELDING TO PRESSURE VESSEL FABRICATION

熔嘴电渣焊在高压容器制造中的应用

Study on Elextro-slag Pressure Welding Equipment of vertical Reinforced Bar…

竖向钢筋电渣压力焊研究——设备部分

Application of Electroslag Pressure Welding of Vertical Reinforcing Steel Bar in Engineering;

竖向钢筋电渣压力焊在工程中的应用

Development of Electroslag Welding Base on PLC

基于PLC的电渣焊控制系统的研制

Thus the fracture likely initiated from fatigue sharpened cracks originating from slag and void in the plug welds.

因此，断裂可能是由于从塞焊焊缝内的焊渣和气孔外形成的尖锐的疲劳裂纹而产生的。