基本释义:

轴端

网络释义

1)shaft end,轴端

2)end axle,端轴

3)tail-end,尾轴端,尾端

4)end journal bearing,端轴颈轴承

5)stirring axial terminal,搅拌轴端

6)roll end sleeve,辊端轴套

用法和例句

New structure of shaft end fixture;

一种轴端处紧固联接的新结构

It is suggested that the vertical stiffness of the mid-axle should be lower than the end axle.

分析了铁路进一步提速对机车牵引动力的要求,从改善机车在既有线路运行时的动力学性能及曲线通过性能出发,对200km/h机车(C0-C0轴式)一系簧有关刚度进行分析计算,认为应使中间轴一系簧垂向刚度小于端轴。

The failure of 40 Cr steel end axle is analyzed by metallographic examination,chemical analysis and mechanical testing.

采用光学显微镜分析、化学成分分析和力学性能试验,对40Cr钢端轴断裂件进行分析。

According to the heat treatment process requirement for the profile control technology of roll end sleeve developed by CLECM Co.

根据法国CLECM公司板形控制技术中辊端轴套的热处理技术条件 ,研究了 18NcD6钢的渗碳淬火工艺、热处理畸变控制及其力学性能 ,成功地实现了新型辊端轴套的国产化 ,产品性能完全达到法国CLECM公司技术标准 ,收到了显著的经济效

Drilling machines-Spindle noses

GB/T2815-1989钻床主轴端部

Dimensions of spindle ends for manually operated electronic components

GB/T2775-1993手控电子元件的轴端尺寸

distance from spindle nose to central line of table

主轴端面至工作台中心线距离

Lock rings at the end of shaft with scre

GB/T891-1986螺钉紧固轴端挡圈

Lock rings at the end of shaft with bolt

GB/T892-1986螺栓紧固轴端挡圈

hub cap for road motor vehicles or tractors

轴端盖,道路机动车辆或摩托车用

Remove vibration damper bolt and washer from end of crankshaft.

从曲轴端拆下减震器螺栓和垫圈。

Retrofit of the Low-pressure Shaft Butt Seal in 51-50-3 Type Steam Turbine

51-50-3型汽轮机低压轴端汽封的改造

fan end thrust ball bearing

风扇端止推滚球轴承

axial double mechanical seal

轴向双端面机械密封

SMALLER DIAMETER OF PIVOT BEARING

轮毂轴承的较小直径端

End play in drive pinion bearings.

驱动小齿轮轴承的端隙。

vertical -spindle double ended grinding mahcine for piston ring

活塞环立轴双端面磨床

horizontal spindle double ended grinding machine for piston ring

活塞环卧轴双端面磨床

Pressure-compensated air bearings are used on both ends of the trunnion axis.

耳轴两端各用一压力补偿空气轴承。

Measures for improving the concentricity of the bearing s minor hole at the two ends;

提高套筒两端轴承档内孔同轴度的措施

The dates you specified for the axis values can't be used, because the maximum axis value must occur at a later date than the minimum axis value.

为坐标轴指定的日期非法。坐标轴远端的日期必须晚于近端的日期。

Either extremity of an axis through a sphere.

（轴的）两极穿过一个球体的中轴的两端中的任一端