基本释义:

锥形回转阀

网络释义

1)conical rotary valve,锥形回转阀

2)return cone valve,回料锥形阀

3)cone rotary kiln,锥形回转窑

4)cone valve,锥阀，锥形阀

5)gyratory cone crusher,回转锥形压碎机

6)cone valve,锥形阀

用法和例句

The constructions of return cone valve and deslagging cone valve in domestic 300 MW CFB boiler were in- troduced,the problems often occurred in the two cone valves operation were described,and the reasons causing these problems were analyzed.

介绍了国产300MW CFB锅炉回料锥形阀和排渣锥形阀的结构,指出了2种锥形阀在运行中经常出现的问题,分析了出现这些问题的原因并针对这些问题提出了相应的措施。

Based on the discussion of some design and operation parameters of coke calcination rotary kiln, the design of cone rotary kiln and its feasibility and superiority in practical use are introduced.

通过对焦炭煅烧回转窑的一些设计和运行参数的讨论 ,论述了锥形回转窑的设计及其使用的可行性和优越性。

After the Kongdong reservoir water hole plate gate rebuild into a cone valve,the stilling basin,model test was conducted.

对崆峒水库输水洞平板闸门改建为锥形阀后的消力池进行了模型试验研究。

Fluid control one-way valve used cone disc, sealed a good performance.

液控单向阀采用锥形阀芯，因此密封性能好。

The taper stem head then transfers a vertical closing force to a lateral force which positively seats the knife against the seat face.

然后锥形阀杆头将垂直关闭力转换成侧向力，将闸刀放置到阀座表面上。

Non-lubricated, tapered plug assures tight seal with low breakout torque. Constructed of hardened materials with optional hard facing.

无润滑，锥形阀塞确保紧密密封，并且具有很低的启动扭矩。有硬化材料构造而成，配置备选硬面。

Numerical Simulation for Flow Field of Conical Wing Valve Based on Fluent

基于Fluent的锥形节流阀流场数值模拟

Optional disc configuration which provides line contact between spherical disc and conical body seat.

备选阀瓣结构，在球形阀瓣和锥体阀座之间具有线接触作用。

The Optimization and Experimental Research of Valveless Piezoelectric Pump with Changeable Nozzle/diffuser Elements;

连续可变锥角的锥形流管无阀压电泵的优化与实验研究

The opposite end is tapered to a small opening that is threaded to accommodate the installation of a valve.

另一端是锥形开口，车有螺纹，以便安装阀门。

The valve realizes discharging using trimming moment.

锥形锁风阀利用力矩平衡的方法实现卸灰。

A tube is a pipe tapered at both ends. Each end is threaded to allow the installation of valves, connections, or relief devices.

管道两端是锥形。每一端都车有螺纹，以安装阀门、接头或减压装置。

special taper thread tap for gas cylinder

气瓶专用锥形螺纹丝锥

If a means of sealing the shell tapping is provided, it shall be suitable for the full pressure/ temperature rating of the valve.

如果提供了用于密封筒形丝锥的工具，这个工序必须适用于阀门所有压力/度等级。

CFD Study for the Flow Filed Inside the Hydraulic Poppet Valve Considering of the Movement of Cone;

阀芯运动过程液压锥阀内部流场的CFD计算

Analysis on Flow Force of the Hydraulic Poppet Valve with the Moving Cone Based on CFD;

基于CFD的液压锥阀阀芯启闭过程的液动力分析

Steady-state Fluid Force Direction of Comparative Analysis about Slip Valve and Cone Valve

关于滑阀与锥阀中稳态液动力方向的比较分析

Design of Pneumatic Gauge Head for Valve Body's Taper of Wedged Odd Gate Valve

楔式单闸板阀门阀体锥度气动测头的设计

Study on Weakening for Cone-valve Typed One-way Valve Based on Its Structural Parameter Optimization

基于结构参数优化的锥阀式单向阀消振研究

conical thin-layer chromatography

锥形薄层色谱(法)

conical bellows

圆锥形(伸缩)风箱