基本释义:

转子间隙配合

网络释义

1)close sliding fit,转子间隙配合

2)Clearance fit,间隙配合

3)tolerance clearance,配合间隙

4)fit clearance,配合间隙

5)Clearance,配合间隙

6)rotor clearance,转子间隙

用法和例句

This paper introduced the tolerance clearance for sleeve jointing tubes with an inorganic and three organic bonding agents.

以钢铁试样为模拟试样研究了大直径钢铁试样与陶瓷试样套接的适用胶粘剂和配合间隙。

The impact of the fit clearances of kinematic pairs on the performance of the liquid-jet hammer;

运动副配合间隙对射流式液动锤性能的影响

Based on finite element method,stiffness characteristics were investigated under different whirling angle,pedestal parameters,and fit clearance,to present guidance for design of elastic ring.

本文针对两种弹性环刚度的计算方法——解析法和有限元法进行了对比,分析了各自的适用条件,并基于有限元法分析了涡动角、凸台参数和配合间隙对弹性环刚度的影响,为弹性环的结构设计提供了参考。

The effect of fit clearance between hoping strips and blades orifices on the stress distribution on blade was explored.

针对某航空发动机低压涡轮工作叶片建立了全尺寸有限元模型·根据台架试验及实际工作承载条件,综合考虑叶片工作时所承受的离心负荷与气流力,进行了弹塑性有限元分析;研究了箍带与叶身小孔的配合间隙对结构应力场分布的影响,发现叶片结构强度的薄弱之处为榫头第一喉部、叶身小孔及叶背一侧圆根处·以此为依据,对叶片进行了高温低循环疲劳寿命预测·计算结果表明:叶身小孔与箍带的最大配合间隙对结构静强度及寿命影响较大,寿命计算时应当考虑平均间隙量的影响;随着计算温度的提高,寿命计算结果大幅度下降

The results show that the clearance of spool and valve body should be controled within 0 007 mm, error of centralization of throttle valve within 30%.

结果表明 :应将阀芯和阀体的配合间隙控制在 0 。

The clearance between oil distribution axle and rotor of radial piston pump can directly influence the performance and life of pump.

径向柱塞泵配油轴与转子配合间隙直接影响着泵的性能和寿命。

Effect of rotor clearance to the gap regulating mixer;

转子间隙对调距式密炼机的影响

Influence of spline matching clearance on spline coupling failure;

试析配合间隙对花键联结失败的影响

It presents an easy method to control the machining accuracy of thread with high requirement for fit clearance.

介绍配合间隙要求高的螺纹副的一种简易加工精度控制方法。

The Effect of Integral Key Fit Clearance beyond the Tolerance of Rolling Mill Screw-down Motor on Service Performance of Rolling Mill

轧机压下丝杆花键配合间隙超差对轧机使用性能影响的分析

combine ground clearance

联合收割机离地间隙

Clutch pedal free travel

离合器踏板自由间隙

Reasonable value of optimized negative clearance in fine-blanking with negative clearance

负间隙精密冲裁最佳负间隙的合理取值

Impact of Gradation on Voidage of Rubber Asphalt Mixture

级配对橡胶沥青混合料空隙率的影响

A Retrospective Research of Clinical Results of Anterior Cervical Discectomy and Fusion for the Treatment of Single-level Cervical Disease;

颈前路经椎间隙减压融合术治疗单间隙颈椎病的临床研究

Gap Impedance Simulation of X-Band Three-Gap Coupled Cavity Output Circuit

X波段三间隙耦合腔型输出回路间隙阻抗的模拟计算

Research on the Online Measurement System of Product Gesture and Aassembly Interval;

产品装配间隙及姿态在线测量系统的研究

Experience Calculation for the Voids in the Mineral Aggregate (VMA) Based on Aggregate Gradation

基于矿料级配的矿料间隙率VMA经验计算法

Analysis of Influence of Gradation and Testing Methods on Porosity of Coarse Aggregate

级配及测试方法对粗集料间隙率的影响分析

lower high water interva

低高潮间隙低高潮间隙

gap(p)ing of joints

连接间隙, 接缝间隙

The Test Research on Critical Voids in the Minerals of Asphalt Mixture;

沥青混合料临界矿料间隙率试验研究

Research on 3D Molding and Meshing Clearance of Conical Twin-Screw

锥双螺杆的三维建模与啮合间隙研究

Modified SMA Design Procedure Based on Voids in Mineral Aggregate

基于矿料间隙率的SMA混合料设计新法

The effects of five adjusting parameters of valve timing, admission valve clearance, emission valve clearance, rotational speed ,load rate are interacted.

配气相位、进气门间隙、排气门间隙、转速、负荷五个调整参数之间是相互影响的。