基本释义:

橡胶密封圈，护孔环

网络释义

1)grommet,橡胶密封圈，护孔环

2)rubber seal ring,橡胶密封圈

3)rubber ring,橡胶密封圈

4)seal with elastometic washer,橡胶圈密封

5)rubber seal,橡胶密封圈

6)rubber grommet,橡胶垫圈<密封圈>

用法和例句

Development of rubber seal ring with outer case for push-pull rod;

推拉杆用外嵌骨架橡胶密封圈

Performance analysis of special cross section rubber seal ring;

特殊形状橡胶密封圈的性能分析

The ageing and durability of rubber seal ring for pipe joint were briefly discussed in this paper.

针对管道接口用橡胶密封圈的老化原因和耐久性进行了探

Study of rubber ring with inner case resistance to high temperature;

内骨架耐热橡胶密封圈的研制

This paper introduces a new type of quick connector framework by making use of rubber seal and plastics clip.

介绍了一种利用橡胶密封圈和塑料卡环实现待插管锁紧的新型快插式接头结构。

rubber sealing ring for medical sterite cooker

医用消毒锅橡胶密封圈

rubber sealing ring for pressure cooker

日用压力锅橡胶密封圈

Effects of Dimensional Tolerance on Sealing Characteristic of O-ring;

O形橡胶密封圈尺寸公差对密封性能的影响

Finite Element Analysis on Rubber Sealing Y-ring in the Condition of Static Seal

静密封条件下Y形橡胶密封圈有限元分析

Test methods for rubber O rings

GB/T5720-1993O形橡胶密封圈试验方法

Appearance quality for reciprocating rubber seals

GB/T15325-1994往复运动橡胶密封圈外观质量

Finite Element Analysis of Stress and Contact Pressure of Rubber O-sealing Ring with Back-up Ring

O形橡胶密封圈配合挡圈密封的应力与接触压力有限元分析

Reciprocating rubber seals-Design criteria for standard applications-Part 3: rubber seals for wipers

GB/T10708.3-1989往复运动橡胶密封圈结构尺寸系列第三部分:橡胶防尘密封圈

Appearance quality acceptance criteria for rubber O-rings

GB/T3452.2-1987O形橡胶密封圈外观质量检验标准

The Non-linear Contact Finite Element Analysis of the Mouth Shaped Rubber Sealing Ring

唇形橡胶密封圈非线性接触有限元分析

Study on Effects of Biodiesel on Swelling Performance of Rubber Sealing Collar

生物柴油对橡胶密封圈溶胀性能的影响研究

The Application of Finite Element Method in the Design of Rubber Sealing Y_X-ring

有限元分析法在Y_X形橡胶密封圈设计中的应用

Research on Storage Life of Silicon Rubber O-ring in Different Temperature and Humidity Condition

不同温、湿度条件下硅橡胶密封圈贮存寿命研究

" Fluid systems--Sealing devices--O-rings--Inside diameters, cross-sections, tolerances and size identification code"

GB3452.1-1992液压气动用O形橡胶密封圈尺寸系列及公差

Fluid power systems--O-ring--Design criteria for O-ring housing--Basic calculation

GB/T3452.3-1988液压气动用O形橡胶密封圈沟漕尺寸和设计计算

Simplified two-dimension finite element model was established for the hollow rubber seal of hood-type annealing furnace.

建立了罩式退火炉空心橡胶密封圈的二维简化有限元模型;

Improvement on Rubber Seal Ring of Plastic Bottle-blower Based on Finite Element Method

基于有限元分析的PET吹瓶机橡胶密封圈的改进设计

Medium or High-pressure Seal Design of SrO·6Fe_2O_3 MNBR

SrO·6Fe_2O_3磁性丁腈橡胶中高压密封圈设计