基本释义:

小齿轮磨损

网络释义

1)pinion wear,小齿轮磨损

2)gear wear,齿轮磨损

3)gear tooth wear,齿轮轮齿磨损

4)gear and rack abrasion,齿轮齿条磨损

5)Normal abrasion value of teeth,轮齿法面磨损量

6)log's abrasion life,轮齿磨损寿命

用法和例句

Based on fractal theory, the paper presents a new method of monitoring gear wear by using fractal dimension.

将分形理论用于齿轮磨损的监测,从工程应用角度介绍了振动信号盒维数的计算方法。

Study on Fractal Prediction of Gear Wear;

汽车变速箱齿轮磨损的分形预测研究

Because the grease was almost gone,the gears suffered from serious wear and tear.

由于润滑油差不多耗尽 了,齿轮磨损很严重.

Study of Wear Evaluation of Heavy Duty Gear Based on Oil Analysis;

基于油液分析的重负荷齿轮磨损状态评判的研究

Application of Ant Colony Algorithm Based on Dynamic and Adaptive Adjust Pheromone in Driving Gear Abrasion Categorization

动态自适应调整信息素蚁群算法在传动齿轮磨损归类中的应用

Worn teeth on ring gear or drive pinion gear.

环形齿轮或驱动小齿轮上齿磨损。

Gears--Wear and damage to gear teeth--Terminology

GB/T3481-1997齿轮轮齿磨损和损伤术语

The Method for Determining the Abrasion Value and Abrasion Life of Tooth Surfaces in a Helical Gearing by Means of the Abrasion Experiment

借助磨损实验确定斜齿齿轮机构齿面磨损量及磨损寿命的方法

burnishing of gear teeth

(齿轮的) 轮齿研磨

Worn or defective transaxle gears or bearings

传动齿轮或轴承磨耗或损坏

The helical gear has become worked down over the years.

斜齿轮因为年久而磨损了。

Research on gear′s fretting in wind power station

风电系统中加速齿轮的微动磨损研究

Research of Wear-out-failure of Star-wheel Teeth in Single Screw Compressors

单螺杆压缩机星轮齿磨损问题的研究

Distinctiveness Investigation of Anti-wear Property for Industrial Gear Oils

工业齿轮油抗磨损性能的区分性考察

Research on Wear-Resistance Design on Output Mechanism in Zero Tooth Difference;

零齿差齿轮输出机构耐磨损设计的研究

Cause Analysis of the Idler Gear Wear-out in the Three-roll Compact Device

三罗拉集聚装置中过桥齿轮易磨损原因分析

Research on the Method of Accurate Relief Grinding for Making Gear Hobs

齿轮滚刀齿侧面精密铲磨的方法研究

Check for scores, nicks or burrs on the rack piston finished surfacSlight wear is normal on the worm gear surfaces.

检查齿条活塞抛光表面是否有刮痕、刻痕或磨擦。涡轮表面的轻微磨损是正常的。

Research on the Simulation of Shaping Process and Grinding Principle of Orthogonal-shaft Face Gear;

正交面齿轮的插齿加工仿真和磨齿原理研究