基本释义:

斜面加工

网络释义

1)oblique surface machining,斜面加工

2)inclined plane,斜面

3)slant,斜面

4)slope,斜面

5)Oblique plane,斜面

6)inclined water bottom,斜面

用法和例句

One of them is used for clamping workpieces with small angle inclined plane, other two kinds are used separately for rectangular paralleling workpieces and cylinder workpieces.

基于冲击与自锁原理,以圆柱体为夹紧元件,设计了加工小角度斜面零件用夹具和装夹长方体类、圆柱体类零件的夹具,分别给出了它们的工作限制条件和力学计算公式。

Based On the analyzing of the principle factors that influence the quality of the knee bend mould , the special grinder fixtures used in grinding inclined plane of knee bend mould are designed in the paper.

在分析影响某折弯模具产品质量的主要原因基础上,针对折弯模具刀口斜面的磨削关键工序进行了专用磨床夹具设计。

In this paper,die design for cut tongue bending part with double inclined plane and knife mouth are introduced,for cut tongue bending part with single plane.

通过理论分析 ,介绍了双斜面刃口切舌弯曲模的设计方法及单面切舌零件的卸料及防止垂直切口撕裂的方

The manufacture of the multifunctional device for shelving medium slant used in the microbiological experiment;

微生物学实验中多用培养基斜面搁置器的制作

In terms of defects of the traditional oblique wedge die with several side holes that had position degree at the same product,method of integration with rotating wheel and slant was adopted.

针对传统的斜楔模在同一制件上冲制有位置度要求的几个侧孔时的缺点,采用转动盘与斜面相结合的方式,在同一副模具上同时冲出有位置度要求的4个孔。

Construction technique of pouring thin concrete layer on the old one after making the slope surface rough;

斜面凿毛后在老混凝土上浇筑薄层混凝土的施工技术

The measuring methods and computers data processing of the slope were introduced.

介绍了斜面的测量和计算机处理数据的方法,主要研究最小二乘原理下的数据处理,应用C语言编程处理,大大提高了斜面测量的精度和运算速度。

According to the results of stress calculation, provided the choosing basis for structure parameters of hydraulic cylinder and advanced a new cylinder bottom structure-oblique plane check ring concave groove.

对 10MN闭模挤压液压机卡环式液压缸进行有限元应力分析 ,根据分析结果 ,给出了液压缸缸底结构参数的选取依据 ,并在此基础上提出了一种斜面卡环凹槽新结构 ,有效解决了大型卡环式液压缸卡环凹槽的应力集中问

The numerical method is applied to analyze both linear and nonlinear wave deformations caused by inclined water bottom.

精确模拟非线性波沿斜面传播过程非常困难,为此论文从势函数的边界积分方程出发,建立了一种时域内二维波浪模拟的数值模型,主要用来模拟完全非线性波浪的传播变形过程。

The numerical method is applied to analyse the linear wave and nonlinear wave deformations caused by inclined water bottom.

线性波的算例也取得了比较理想的造波结果,并且波浪在斜面上传播过程中波形比较稳定。