基本释义:

中间齿轮总成

网络释义

1)idler gear assembly,中间齿轮总成

2)camshaft idler gear assembly,凸轮轴中间齿轮总成

3)fuel pump idler gear assembly,燃油泵中间齿轮总成

4)gear assembly,齿轮总成

5)middle gear,中间齿轮

6)bevel gear assembly,锥齿轮总成

用法和例句

Pressing technology and mould design for powder metallurgy process of middle gear;

中间齿轮粉末冶金压制工艺及模具设计

Analysis of Gasket-selection for Driving Taper Assembly of Automobile s Driving Axle and the System Development;

汽车驱动桥主动锥齿轮总成选垫分析及系统实现

Research and Development on Fatigue Testing System of Gears in Drive-axle Assembly of Automobile;

汽车驱动桥总成齿轮疲劳测试系统的研发

Influences of hypoid gear quality on rear axle noise

螺旋锥齿轮质量对后桥总成噪声的影响

Bending stress analysis on gears of heavy duty automobile gear box based on assembly

基于总成的重型汽车变速箱齿轮弯曲应力分析

Research on Lubricating Oil Temperature Control Strategy of Gears in Drive-axle in Fatigue Testing System of Gears in Drive-axle Assembly of Vehicile

车辆驱动桥总成齿轮疲劳试验台中驱动桥齿轮润滑油油温控制策略的研究

Study on the Formation of Spur Face Gear Tooth Profile and Meshing Simulation;

直齿面齿轮齿面生成方法与啮合仿真

Research and Development on Fatigue Testing System of Gears in Drive-axle Assembly of Heavy-duty Trucks;

重型车辆驱动桥总成齿轮疲劳测试系统的研究与开发

straight-cut gear

直齿圆柱齿轮，正齿齿轮

burnishing of gear teeth

(齿轮的) 轮齿研磨

gear deburring and tooth pointing machine

齿轮去毛刺及齿顶成型机

Transformation from Rack-type Geer Cutter into Geer Hobber.

齿刀是怎么演变成齿轮滚刀的

Forming Mechanism of Tooth Flank Burr in Cutting Gear

齿轮齿形切削加工中的毛刺生成机理

Dynamic Simulation of the Generating Process of Gear Pofile;

齿轮齿廓范成过程的计算机动态仿真

Hot Forging Deformation of Magnesium Alloys AZ31B Spur Bevel Gear

镁合金AZ31B直齿锥齿轮热锻成形研究

Numerical Simulation on Precision Forging of Spiral Bevel Gears

弧齿锥齿轮精锻成形工艺的数值模拟

Research on Influence of Machining Parameters of Generating Method on Tooth Surface of Spiral Bevel Gear

展成法加工参数对弧齿锥齿轮齿面的影响研究

Study on Cold Extruding Forming Technology for the Driving Gear of Saw-tooth Inner Gear

锯齿形内齿主动齿轮冷挤压成型技术研究

Experiences from successful works have been summed up that the crux of improvement is the bearing design of the shaft supporting pulley and gear.

本文总结了成功的改造经验，指出改造中的关键问题是带轮－齿轮轴的支承设计。