基本释义:

中间主轴承盖

网络释义

1)center main bearing cap,中间主轴承盖

2)crankshaft intermediate main bearing cap,曲轴中间主轴承盖

3)plumber block keep,中间轴承盖

4)midship shaft bearing cover,中间轴轴承盖

5)center main bearing,中间主轴承

6)main bearing cap,主轴承盖

用法和例句

Development of a main bearing cap for an inline 6 cylinder engine;

一种直列式6缸发动机主轴承盖的开发

Problems of falling chip, tool tipping and big noise are happened during cutting off main bearing caps made of gray casting by using combination milling cutters.

采用组合铣刀切断灰口铸铁材质的汽车发动机主轴承盖时 ,出现工件掉渣、刀具崩刃、噪声大等问题。

The characteristic analysis of the suspended main bearing cap of SL4105 diesel engine was presented by using the 3D solid modeling,3D mesh generation,external loads & boundary condition and 3D finite element analysis.

介绍一种运用三维实体造型、三维网格划分、载荷和约束处理及三维有限元分析的方法,对SL4105柴油机悬挂式主轴承盖进行了强度和刚度分

Install the lower bearing inserts into the main bearing caps.

安装下轴瓦到主轴承盖。

Measurement of Dynamic Stresses and Temperatures of Main Bearing Walls and Caps on an Engine Block

发动机缸体主轴承座及主轴承盖的动态应力和温度测量

3D Finite Element Analysis of Suspended Main Bearing Cap of Diesel Engine

柴油机悬挂式主轴承盖的三维有限元分析

3D Finite Element Analysis of Stiffness and strength of Main Bearing Cap of Internal combustion Engine

内燃机主轴承盖强度和刚度的三维有限元分析

Remove the lower insert from the bearing cap.

从轴承盖上拆去下轴瓦。

Oil may be forced out through the timing cover and rear-main bearing oil seals.

机油会从正时齿轮盖和后主轴承油封处压出。

upper center crankshaft bearing

曲轴主轴承上中轴瓦

end shield bearing

机油滤清器内盖头轴承

The bottom bearing applies both labyrinth seal and frame seal, which have good performance of sealing. The main shaft is anticorrosive.

下轴承端盖密封采用双重密封，可确保密封效果，主轴采用防腐新技术，能保护主轴免受腐蚀。

Plain Bearing Block Housings are made up of cap, base ,aluminum bronze bushing and installing bolts, which mainly bear radial load.

滑动轴承座由上盖、底座、剖分轴瓦（铝青铜），安装螺栓组成，主要承受径向载荷。

The feed holes for the crankshaft main bearings.

曲轴主轴承进入口。

Crankshaft and main bearings service

曲轴和主轴承的维修

Analysis and solution of cramped shield to be detachable in sealing bearings

带卷边防尘盖轴承活盖问题解决办法

The Model Analysis of the Ceramic Bearing Electric Spindle;

陶瓷轴承电主轴主轴的振动模态分析

These are the same as those used for the main bearings.

这些轴承与那些被用作主要轴承的轴承相同。

Remove thrust bearings from rear main bearing carrier.

从后主轴承托架上拆下止推轴承。

Modeling for Rotor System of AC Magnetic Bearing Electric Spindle;

交流磁轴承支承电主轴转子系统建模

Undersize crankshaft main bearing journals.

尺寸小于标准的凸轮轴主轴承轴颈。