基本释义:

轴承紧固螺栓

网络释义

1)holding down bolt,轴承紧固螺栓

2)bearing pressure bolt,轴承的压紧螺栓

3)flanged shaft securing bolt,法兰轴紧固螺栓

4)fastening bolt axial force,紧固螺栓轴力

5)main bearing steadying bolt,主轴承固定螺栓

6)bearing retaining bolt,轴承固定螺栓

用法和例句

Experimental Study on Fastening Bolt Axial Force of WSGG Anchor Basted on CFRP Sheet

CFRP波形齿锚具紧固螺栓轴力的试验

Lock rings at the end of shaft with bolt

GB/T892-1986螺栓紧固轴端挡圈

Reason for Low Tight Axle Strength of 10.9S Sets of Torshear Type High Strength Bolt for Steel Structures

钢结构用10.9S扭剪型高强螺栓连接副紧固轴力偏低原因分析

Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.

在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。

Inspect crankshaft, flexplate/flywheel and bolts for damagTighten to correct torque

检查曲轴、活动板/飞轮和螺栓是否松动。拧紧螺栓以校正扭力。

" Tolerances for fasteners--Bolts, screws and nuts"

GB/T3103.1-1982紧固件公差螺栓、螺钉和螺母

hydrauliccone-bolt coupling

液力锥形螺栓联轴器

Fasteners--Clearance holes for bolts and screws

GB/T5277-1985紧固件螺栓和螺钉通孔

Axis positioning buildings, infrastructure and elevation axes, anchor bolt fastening should conform to the specifications and design requirements.

建筑物的定位轴线、础轴线和标高、脚螺栓的规格及其紧固应符合设计要求。

" Mechanical properties of fasteners--Bolts, screws and studs"

GB/T3098.1-1982紧固件机械性能螺栓、螺钉和螺柱

Without live-loading, bolt tightness will be lost, when the system loses pressure.

没有动负载，当系统失去压力时，螺栓紧固性就会丧失。

Replace the body bolts and tighten evenly.

重新放置阀体螺栓，并均匀紧固。

Tighten exhaust manifold to cylinder head bolts.

紧固排气岐管汽缸头螺栓。

Study on Localization Technology of Bolt Fasteners for CPR1000 Internals

CPR1000堆内构件螺栓紧固件的转化设计

Install the straps and bolts to hold the propeller shaft to the yoke.

安装扣夹和螺栓，将传动轴固定到轴轭上。

Fasteners--Counterbores for hexagon bolts and nuts

GB/T152.4-1988紧固件六角头螺栓和六角螺母用沉孔

The rear axle is stationary, and is bolted rigidly to the main frame.

后轴是固定的，用螺栓刚性固定在主机架上。

" Fasteners--General requirements for blots,screws,studs and nuts"

GB/T16938-1997紧固件螺栓、螺钉、螺柱和螺母通用技术条件