基本释义:

轴向压力负载

网络释义

1)axial pressure load,轴向压力负载

2)loaded capability,轴向负载能力

3)axial load,轴向负载

4)axial press capacity,轴向受压承载力

5)axial compressive load,轴向压力载荷

6)Load pressure,负载压力

用法和例句

By analyzing elastic distortion and contact form of deep groove ball bearing based on axial load is pressured between sleeve and ball,according to safe contact angle on condition that each component of bearing s relative displacement,the axial loaded capability for bearing can be estimated.

分析了深沟球轴承在轴向载荷作用下套圈与滚动体对压所产生的弹性变形及接触形态,以各元件相对位移时的安全接触角为依据,估算轴承的轴向负载能力,从而对选择轴承的型号提供参考[1]。

So, it has great engineering significance to increase the axial press capacity and ductility of RCSSC in the same area of the section.

因此,如何在保持现有截面的大小的情况下,同时提高异形柱的轴向受压承载力和柱的延性具有重要的工程意义。

This paper presents a new concept of asymmetrical valve controlled asymmetrical cylinder,makes new definition of load flow and load pressure,thus illustrated static and dynamic properties of asymmetrical cylinders,derives its transfer function and block diagram,which can be universally applied to all kinds valve controlled cylinder and may be a meaningful guide to the design of such servo systems.

提出了非对称阀控制非对称缸的概念 ,并对传统的负载流量和负载压力重新进行了定义 ,依此对非对称阀控制非对称缸的静态特性和动态特性进行了分析 ,推导了其传递函数及方框图 ,其推导过程对此类伺服系统的设计具有积极的指导意

According to the working characteristics of the pump and valve combined EHA (Electrical Hydraulic Actuator), the method to improve the system efficiency by increasing the design value of load pressure was proposed.

分析了导致飞行器液压作动系统温度升高的主要因素以及采用多级供油压力提高效率的可行性,针对泵阀联合EHA(电动静液作动器)的工作特点,提出了提高负载压力设计值提高效率的方法,在负载相同的条件下,对伺服阀和定量泵的输出流量、损耗流量变化、作动系统整体效率变化进行了分析。

Bearings shall be specifically selected to carry all radial and axial loads imposed by the pump and motor.

这些轴承都是经过特别挑选,能够承担由泵和电机产生的径向和轴向负载。

Full enclosure to allow gasket to retain positive radial support during loading.

在负载期间，全封闭外科使得垫圈能够保持正轴向支撑。

Metal - Axial load fatigue testing???

金属－－轴向负荷疲劳试验

Most Bearings support rotating shafts against either transverse (radial) or thrust (axial) loads.

大多数轴承都支承径向或轴向负荷的转轴。

The weight of the load swayed the boat to the left.

负载使船侧向左边。

General specification for coaxial line electrical dummy loads

GB/T12774-1991同轴电气假负载总规范

Deep groove ball bearings mainly take radial load as well as take moderate axial load.

深沟球轴承主要承受径向载荷，也可承受一定量的轴向载荷。

Axial load-deformation curve and preload on angular con act ball bearings

角接触球轴承的轴向载荷—变形曲线和预紧

The Research on Equal-strength Design of Large-scale Heavy-load Cross-shaft Universal Clutch

大型重载十字轴式万向联轴器等强度设计研究

This paper describes the design method of broad band coaxial termination load.

本文叙述了宽带同轴终端负载的设计方法.

Study of Simulate and Control of Single Axis Electric Platform with Great Load;

大负载单轴电动转台的仿真与控制研究

Design for Realtime Tracking-Control System of Two-Shaft Turntable;

变负载两轴转台实时跟踪控制系统的设计

Bearing selection shall limit the bearing temperature rise to a maximum of 60 C under full load operation.

在全负载状态下,所挑选的轴承将轴承温度限制在60℃以下。

Design and Optimization of Double-Axes Turning Machenism on Heavy Vehicles;

重载汽车双轴转向系统的设计与优化

Numerical investigation on interaction of axial and lateral response for super-long pile

轴-横向荷载作用下超长桩数值模拟

The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing.

为了避免划伤，轴承上的最大负荷应该总是小于其卸载负荷。

The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing and brineling.

为了避免划伤和压坑，轴承上的最大负荷应该总是小于其卸载负荷。

Four pionts angle contact ball bearing is separable bearing,it can be subject to bi-directional load and have the function of both single row and double rows bearings.

四点接触球轴承为可分离型轴承，可承受双向轴向载荷，并有单列和双列角接触球轴承的功能。