基本释义:

装入方式

网络释义

1)load mode,装入方式

2)integral pump,装入式泵

3)injection pattern,注入方式

4)enter material way,入料方式

5)permeating pattern,渗入方式

6)injection manner,注入方式

用法和例句

This paper studies the factors including injection pattern, injection procedure and slug size which influence the displacement efficiency of loam flooding.

针对影响泡沫复合驱驱油效率的注入方式、注入程序及段塞大小等重要因素进行了一系列的研究。

First, we had done the research on the injection pattern and measurement of viscoelasticity of the ternary compound systems with each kind of polymer, respectively, from which concluded that resistance factor and residual resistance factor increased as the increasing of the concentration of polymer, and so the viscoelasticity did.

首先对六种聚合物复配的三元体系进行了注入方式的研究并进行了粘弹性的测定,得出了随着体系中聚合物浓度的增加,体系的阻力系数和残余阻力系数都呈增大的趋势,而且随着体系中聚合物浓度的增加,体系的粘弹性也呈增大的趋势;在人造岩心上进行了不同聚合物、不同渗透率条件下的三元复合驱物理模拟实验,得出三元复合体系具有良好的波及体积的能力;选出最佳的聚合物后进行了对主段塞的优化,得出了最佳的段塞大小优化组合。

layer,composition of the layer, permeating pattern and composition in.

结果表明：渗层具有良好的热稳定性，同时指出了渗剂配方、渗层组织结构、成分、渗入方式之间有着十分密切的联系。

Through numerical simulation and physical simulation,the influences of injection manner,different contact relations and different injection velocity ration on the development effect of the contact zones of polymer flooding and wat.

通过数值模拟和物理模拟手段研究不同注入方式、不同接触关系、不同注入速度比等因素对聚水驱接触带开发效果的影响。

The Study on Property Evaluation and Injection Improvement for Foam System

泡沫复合体系性能评价及注入方式优化研究

Studies on the Mechanism of ASP and the Injection Optimization of ASP Flooding

三元复合驱驱油机理及注入方式优化研究

Fluid Injection Method in Super High Speed Point Grinding

超高速点磨削工艺磨削液的注入方式研究

The molten metal may enter the ingot mould in two ways: from the top and from the bottom.

钢液注入钢锭模可采用两种方式:上注和下注。

The slug of tracer is added to the stream in an undefined manner.

示踪剂液滴以不确定的方式注入流注里。

In what form is the CO2 injected underground?

二氧化碳注入地下是以何种方式存在？

The molten metal may enter the ingot mould in two ways: from the top and from the bottom. Top pouring is the simplest and cheapest method, but gives poor control over the rate of pouring.

钢液注入钢锭模可采用两种方式:上注和下注。上注法最简单，成本最低，但不好控制浇注速度。

The traditional way of life of the Tibetan people has been somewhat modernized.

藏族人民传统的生活方式注入了现代化的内容。

Research on Method of Put Human Element into Product s Information Transmit;

产品信息传达中注入人文要素的方式研究

Compound Control Method for Single Injected Active Power Filter

单独注入式有源滤波器的新型复合控制方法

Novel injection protection scheme for stator ground fault of pumped storage generator

抽水蓄能电站发电机注入式定子接地保护方案

STUDY OF THE THERAPEUTIC EFFECT OF INTRATRACHEAL INJECTION OF PULMONARY SURFACTANT WITH DIFFERENT METHOD

不同方式注入肺泡表面活性物质的疗效观察

Taken into the body or administered in a manner other than through the digestive tract, as by intravenous or intramuscular injection.

不经肠的，注射用药物的不经过消化道而用静脉注射或肌内注射的方式进入体内或服用的

injected-beam forward amplifier

注入式前向波放大管

gallium arsenide injection laser

砷化镓注入式激光器

bistable injection laser

双稳态注入式激光器

stab-in cementing shoe

插入式注水泥用套管鞋

injection semiconductor laser

注入式半导体激光器