基本释义:

排出动压头

网络释义

1)dynamic delivery head,排出动压头

2)discharge pressure head,排出压头

3)static delivery head,排出静压头

4)discharge head,排出压头，输送压头，出口压头，(泵)扬程，出口压力

5)discharge pressure,排出压力

6)bar actuated pressure vent,杆式驱动液压排出孔

用法和例句

Fuzzy control of the discharge pressure of sand pump during refracturing;

重复压裂砂泵排出压力的模糊控制

maximum output pressure(absolute)

(绝) 最高排出压力

Leaks can occur along the valve stem through the packing or diaphragms. Leaks of this type can be stopped by closing the valve and venting any pressure from the outlet.

泄漏可能沿着阀杆通过衬垫或隔膜发生。关闭阀门，从排气口排出压力可以停止这种泄漏。

Equally effective in checking back flows from head pressure on the discharge or suction sides of pump.

无论是泵的排泄口的排出压力，还是泵的吸入口，其流体止回的效果都是相同的。

used to force a liquid up and expel it under pressure.

使液体上升并在压力下排出的泵。

the pressure activates the tripper and releases the water.

压力使机器开关生效并且把水排出去。

The compression of the soil under the applied stresses would force some water out of the voids.

施加压力压缩土壤会使一些水从孔隙中排出。

Research of Measuring Method on the Pumpage of Concrete Pump Based on Discharge Pressure;

基于出口压力的混凝土泵排量测量方法研究

Analysis and countermeasures of phenomena of wet pack after pressure steam sterilization;

压力蒸气灭菌出现湿包的原因分析及排除方法

discharge pressure

（气压机的）排放压力

bar actuated pressure vent

杆式驱动液压排出孔

firedamp pressure-chamber method

瓦斯压力调节室排放法

exhaust pressure controlled EGR system

排气压力控制式EGR系统

"As thermal expansion conditions develop, pressure builds up to the setting of the relief valve. This will cause discharging of small quantity of water."

随着热量的增加,压力也随着增加,并达到安全阀的压力设置。此时将导致安全阀排泄出少量的水。

(3)The distribution of the bore pressure along vertical space which is a new type loading mode for the design of pile-groin.

(3)涌潮压力在垂线方向上的分布。 为排桩式丁坝的设计提出了新型的受力模式。

With the compressor clutch engaged, record the discharge air temperature and the compressor discharge pressure.

当压缩机离合器合上时，记录排放空气温度和压缩机排放压力。

A jet engine having a turbine-driven compressor and developing thrust from the exhaust of hot gases.

涡轮喷气发动机一种喷气式发动机，有一个涡轮推动的压气机，通过排出热气而产生推力

Vacuum created in cooling system on engine cool-down is not being relieved through pressure/vent cap.

引擎冷却时在冷却系统中产生的真空没有通过压力/排气盖释放出去。

Conversely, by opening the bleed, line pressure will blow out any accumulation when the plug is lifted.

反过来，通过开启排气装置，当阀塞升起时，管路压力将吹出任何累积物。