基本释义:

凝固收缩

网络释义

1)solidification shrinkage,凝固收缩

2)Solidification Feeding,凝固补缩

3)bleeding,凝胶收缩

4)setting shrinkage,凝结收缩

5)curing shrinkage,固化收缩

6)solid contraction,固体收缩

用法和例句

The effect of mechanical vibration on grain refinement and solidification shrinkage of aluminum was investigated in this paper.

研究了振动场对纯Al晶粒细化和凝固收缩的影响,并着重进行理论分析。

The several theory problems that should be paid more attention to,including heat flow rate,solidification shrinkage,mould wall distortion,taper design and corner radius,are put forward and illuminated.

提出并论述了高速方坯连铸结晶器冶金中结晶器热流、钢的凝固收缩、结晶器变形、锥度设计和圆角半径等问题,重点讨论了拉速、碳含量及润滑剂对热流的影响,不同碳含量的钢凝固收缩和相变特征以及结晶器热变形规律,提出了不同钢种的凝固收缩和相变收缩的计算方法和结晶器锥度、圆角半径的设计思路。

Solidification Feeding of Cast Alloy in Investment Casting;

熔模精密铸造合金凝固补缩问题的研究

Through analyzing the density of vacuum counter-pressure casting samples under different keeping pressures,their solidification feeding behavior and mathematical model were discussed.

对不同保压压力下真空差压铸造试样致密度进行分析,探讨真空差压铸造工艺的凝固补缩特性,建立凝固补缩过程的数学模型。

Research status of adjusted pressure casting technology was reviewed from filling capacity, properties of solidification feeding and mechanical properties respectively.

介绍了调压铸造技术的原理及其工艺特点,从充型能力、凝固补缩特性、力学性能等方面评述了目前调压铸造技术的研究现状;结合实际生产应用情况,展望了我国调压铸造技术的发展前景,并对我国发展调压铸造技术提出了一些建议。

Through the optimization of processing conditions in SMC mold, the optimum pressure release time and the pressure in the second stage are determined , and molding runs are carried out at two-stage pressure, and the mold temperature is reduced as appropriate to reduce curing shrinkage and improve surface-quality in SMC molding.

可显著降低SMC制品的固化收缩率,提高其表观质量。

Based on two kinds of silver powder with different morphology and three matrixes with different curing shrinkage, six electrical conductive adhesives were prepared.

选用三种不同固化收缩率的基体树脂和两种银粉,分别配制了六种导电胶。

Based on two kinds of silver powder with different morphology and three matrixes with different curing shrinkage,six electrical conductive adhesives(ECA) were prepared.

采用2种不同形貌的银粉、3种不同固化收缩率的导电胶基体配制6种导电胶,研究等温固化过程中导电胶基体的固化收缩率以及银粉形貌对导电胶电阻率的影响,探讨导电胶的导电机理。

Development and Application of Tester with Twin Bar for Alloy Solidification

双试棒合金凝固收缩力试验机的研制及应用

FINITE ELEMENT MATHEMATICAL MODEL OFINTERDENDRITIC LIQUID FLOW INCONSIDERATION OF EFFECT OFSOLIDIFICATION SHRINKAGE

计及凝固收缩的液固两相区中流场的有限元计算模型

Analytical study on new and old concrete shrinkage difference in bridge reinforcement

桥梁加固新老混凝土收缩差分析研究

Simulation for Shrinkage Defect in Nodular Cast Iron Solidification Process;

球墨铸铁件凝固过程收缩缺陷模拟研究

These blow holes counteract the shrinkage which occurs during solidification and no pipe is formed.

这些气泡抵消了凝固时出现的收缩，因此不会形成缩孔。

The Interface Stress Analysis of the Shrinkage Creep on Anchor Concrete Strengthening Structure

收缩徐变对锚喷混凝土加固结构产生的界面应力分析

To develop conical cavities during solidification.

形成缩管凝固时形成缩孔

Drying Shrinkage and Autogenous Shrinkage Experimental Research of High Performance Concrete;

高性能混凝土的干燥收缩和自生收缩试验研究

Research for Effects of Admixture and Shrinkage Model on High-performance Concrete

掺合料对混凝土收缩影响及收缩模型分析

Solidification Process Simulation and Shrinkage Cavity Prediction of Car Gear Box

汽车齿轮室凝固过程数值模拟及缩孔、缩松预测

coagulation factor IX

干燥浓缩人血凝固第IX因子

Study on Heating and Solidification Microstructure of Upset AZ91D Mg Alloy in the Semi-solid State;

压缩形变AZ91D镁合金半固态加热及凝固组织研究

Research on Chemical Shrinkage and Dry Shrinkage Behavior of Alkali Activated Slag Cement and Concrete;

碱矿渣水泥与混凝土化学收缩和干缩行为研究

Influence of shrinkage-reducing admixtures on the reduction of plastic shrinkage cracking in concrete

减缩剂对减少混凝土塑性收缩裂缝的影响

compression process gasoline

压缩冷凝法回收的天然汽油

Test methods for dry shrinkage of aerated concrete

GB/T11972-1997加气混凝土干燥收缩试验方法

the separation of liquid from a gel that is caused by contraction (as in cheese making).

由于收缩使液体从凝胶体渗出的过程。

Discussion About Concrete Shrinkage Strain Introduced in New China Code for RC and PC Bridges and Culverts

关于新《桥规》中混凝土收缩应变的讨论