基本释义:

射注速率(压铸)

网络释义

1)shot speed,射注速率(压铸)

2)injection transfer mo(u)lding,注射压铸

3)Injection velocity,注射速率

4)injection speed,注射速率

5)injection rate,注射速率

6)Injection Power of Die Casting Machine,压铸机压射功率

用法和例句

Studies on Inversion of Injection Velocity in Injection Molding Based on CAE Technology;

基于CAE技术的注塑模注射速率反演研究

The excellent properties of resin and fiber would be fully embodied through the proper propessing technique and conditions, extrusion temperature, extrusion rate, injection speed are the important factors influencing material property.

结果表明,适宜的加工工艺和加工条件能够将ABS和玻璃纤维本身的优良性能充分表现出来,挤出温度、挤出速度及注射速率都是影响材料性能的重要因素。

The effect of injection rate on the accuracy of the parts injection-molded with PA1010, PA6 and HDPE was discussed by use of the molds of pin gate and of direct gate.

通过点浇口和直浇口模具 ,采用 PA6、PA10 10和 HDPE探讨了注射速率对注射制品精度的影响。

Through practical exprimental tests,the effect of injection rate and the dimension of feed head on calculating plastic flow distance ratio was given.

通过实验指出了注射速率和浇口尺寸对塑料流动距离比计算公式影响较大，提出了改进流动距离比计算公式的途径以及校核现有资料中流动距离比数据时应注意的一些问题。

Objective To investigate the suitable injection rate and dose in multi-slice CT perfusion imaging.

目的探讨多层螺旋CT脑灌注成像合适的注射速率及剂量。

Effects of Injection Power of Die Casting Machine on Quality of Die Castings;

核查压铸机压射功率平衡对压铸件品质的影响

Studies on Inversion of Injection Velocity in Injection Molding Based on CAE Technology;

基于CAE技术的注塑模注射速率反演研究

An Experimental Study about Contrast Medium Injection Rate and Dose in Cerebral CT Perfusion Imaging;

脑CT灌注成像对比剂注射速率与剂量实验研究

The scan cover, injection rate and reconstruction matrix were assured.

确定增强扫描范围、佳注射速率与重建矩阵。

The flow balance in the sub-runner of mould is sensitive to injection rate of plastics melt.

结果表明,注射速率对流道平衡问题是非常敏感的。

The insulin-dosage rate is set in the electronic controller according to the patient's needs.

胰岛素的剂量注射速率，可根据病人的需要在电子控制器中预先制定。

Contrast Quantity and Injection Velocity in Cerebral Angiography with 64 Multi-Detector CT

多层螺旋CT脑血管成像中适当降低对比剂浓度和注射速率观察及探讨

Comparison of the Safety and Effectiveness of Intravenous Metoprolol Versus Cedilanid in the Management of Rapid Ventricular Rate in Atrial Fibrillation;

静脉注射倍他乐克和西地兰控制快速房颤心室率的疗效对比观察

radiation-enhanced burning rate

辐射增强的燃烧速率

the rate of flow of radiant energy (electromagnetic waves).

辐射能流动速率（电磁波）。

Injection System Control Analysis and Simulation Study of Ultra High Speed Injection Machine

超高速注射机注射控制的系统分析与仿真研究

The Research on High Power and High Speed Transmitter of the Free Space Laser Communication;

高功率高速率FSLC发射单元的研究

Note that the words "velocity"and "speed"require explanation.

请注意，“速度”和“速率”这两个词需要解释。

Less reflective than ice, water absorbs more solar rays, speeding the thaw and channeling meltwater into seals' breathing holes.

比冰的反射率小，海水吸收了更多的阳光，加速了融化并使融化后的淡水注入这些通气孔。

Deposition rate is increase quickly with sputtering power.

结果表明溅射功率对沉积速率的影响最大，随溅射功率的增大沉积速率快速增大。

Study on FI Fast Determination of Chemical Oxygen Demand;

流动注射快速测定化学耗氧量的研究

Rapid Manufacturing of Hard Injection Mould Based on RP and CAE Technology

基于RP和CAE的注射硬模快速制造技术

Model Prediction Iterative Learning Control of Ram Velocity for Injection Molding Machines

注塑机注射速度的模型预测迭代学习控制

Injection Velocity Control in Injection Molding by Iterative Learning Control with Zero-phase Filtering

注塑机注射速度的零相位滤波迭代学习控制