基本释义:

注热水

网络释义

1)hot water injection,注热水

2)hot water injection well,注热水井

3)hot-water injection development,注热水开发

4)water fever,水注射性热

5)recuperated water injected cycle,注水回热循环

6)Hot water injection method,高温热水灌注法

用法和例句

A feasibility study of hot-water injection development for thin-interbedded reservoir with heavy oil: a case of Lower Interval of Du66 block in Shuguang oilfield,Liaohe area;

薄互层状普通稠油油藏注热水开发可行性研究——以辽河曙光油田杜66块下层系为例

The Research of Steam Injection and Hot-water Injection in Cao Tai Buried Hill Construction Cracks High-condensate Oilfield

曹台潜山裂缝性高凝油藏注蒸汽及注热水开采适应性研究

Open several hot water faucets to allow air to escape from the system while the heater if filling.

打开几个热水水龙头,让热水管道中的气体在注水过程中排放出来。

Open the nearest hot water faucet and allow the tank to fill completely with water.

打开最近的热水水龙头，让内胆完全注满水。

Intrauterine Saline Infusion Cycle of Heat Treatment of Dysfunctional Uterine Bleeding Study

循环热盐水宫腔灌注治疗功血的研究

Improvement of the Hot Runner Injection Mold for CBP12 Water Tank Cover

CBP12水箱面罩注射模热流道改进

After piping has been properly connected to the water heater, open the nearest hot water faucet and allow the tank to completely fill with water.

管线正确连接到热水器后，打开最近的热水水龙头，让水完全注满热水器内胆。

"After the installation of all water lines, open the main water supply valve and fill the heater."

安装完所有水管后,打开主要供水阀门,将热水器储水罐注满水。

"For your safety, be aware this water heater is capable of producing hot water at a temperature sufficient enough to cause scalding injury."

注意,本热水器产生的热水温度很高,可能会对烫伤人体。

Connect the hot water supply(3/4 NPT) to the fitting marked“ H”.

将热水管道（/NPT英寸）接到标注“H”的接头上。

INTRAVESICAL INSTILLATION OF PAPAVERINE AND HOT WATER TO TREAT FEMALE URETHRAL SYNDROME

罂粟碱加热盐水膀胱灌注治疗女性尿道综合征

Using a hot plate design and chilled water cooling, cycle time could reach 7s.

使用热板和水冷却，可以达到7秒的注塑周期。

CBI+well washing every 45 days in 22 wells (groupⅢ);

第三类22口井注菌液并热水洗井,洗井周期45天;

Experimental Studies of Intrauterine Instillation of Heated Saline for Endometrial Ablation;

热盐水循环灌注去除子宫内膜的实验研究

A Study on Aquathermolysis for Heavy Oil Upgrading under Steam Injection Conditions

稠油注蒸汽层内水热裂解降黏实验研究

Design of Injection Mould with Wedge-shaped Plate Typing and Hot Runner System for Mineral Water Bottle Parison

楔形导板分型矿泉水瓶坯热流道注塑模设计

Analysis of Advantages and Disadvantages of Low Temperature Hot Water Floor Radiant Heating and Construction Attention Issues

简析低温热水地暖的优缺点及施工注意事项

Questions deserving attentions in design of low temperature hot water floor radiation heating system

低温热水地面辐射采暖设计应注意的问题

Water source heating pump system design and problems need attention in construction

水源热泵系统设计及施工中应注意的问题