基本释义:

轴承的压紧螺栓

网络释义

1)bearing pressure bolt,轴承的压紧螺栓

2)holding down bolt,轴承紧固螺栓

3)bearing,轴承螺栓

4)pinion bearing retainer bolt,小齿轮轴承夹紧螺栓

5)press(ure) bolt,压紧螺栓

6)bearing block bolts,轴承座螺栓

用法和例句

The defomations of synchroshaft of step cooling bed in the plant causes the bearing block bolts broken and the inner wall of lift cylinder serously and eccentriclly worn.

涟钢三炼钢厂1#步进冷床下降速度慢且不能到达终点、轴承座螺栓断裂和升降油缸内 壁严重偏磨的主要原因是同步轴严重变形,本文针对同步轴变形提出了改进措施。

Contact analysis of MW wind turbine hub and bearing bolt connection

风力机轮毂和轴承螺栓联接接触分析

The Fracture Failure Analysis on Main Bearing Bolts of the Diesel Engine and Investigation on Its Loading Behaviours;

柴油机主轴承螺栓断裂及其承载力学行为的研究

Bolt( screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.

螺栓（钉、帽、头螺栓、簧垫圈、、珠轴承、柱轴承）最常用的机械零件。

377 bolt (screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.

螺栓（螺钉、螺帽、双头螺栓、弹簧垫圈、销、滚珠轴承、滚柱轴承）是最常用的机械零件。

Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.

在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。

hydrauliccone-bolt coupling

液力锥形螺栓联轴器

Research and Design on the Backpressure Device and Bolt Assembly System in the Fracture Splitting Equipment of Main Bearing Walls on an Engine Block;

缸体主轴承座裂解加工背压装置及螺栓装配系统研制

Research and Design on Automatic Assembling Bolts System for Fracture Splitting Crankcase Bearing Block of Engine;

裂解发动机箱体主轴承座螺栓装配系统研究与设计

Plain Bearing Block Housings are made up of cap, base ,aluminum bronze bushing and installing bolts, which mainly bear radial load.

滑动轴承座由上盖、底座、剖分轴瓦（铝青铜），安装螺栓组成，主要承受径向载荷。

Remove nuts, U-bolts and spring bracket from axle.

由车轴拆下螺帽，U型螺栓和弹簧支架。

Front Stub Axle To Hub Bearing Nut

前螺桩轴至轮毂轴承螺帽

Research on the Influences of Internal Oblique Nut on Bolt Bearing Capacity

内斜螺母对螺栓承载能力影响的研究

spring seat bearing adjusting nut

弹簧座轴承调整螺母

wheel hub bearing adjusting nut

车轮毂轴承调整螺母

Lock rings at the end of shaft with bolt

GB/T892-1986螺栓紧固轴端挡圈

Bushing Retainer To Axle Attaching Bolts

衬套扣环与车轴接合螺栓

Remove vibration damper bolt and washer from end of crankshaft.

从曲轴端拆下减震器螺栓和垫圈。

Tie Rod End Adjusting Sleeve Nut

转向拉杆端调整轴筒螺栓