基本释义:

主轴承拆卸

网络释义

1)main bearing removal,主轴承拆卸

2)bearing removal,轴承拆卸

3)shaft bearing replacer,轴承拆卸器

4)gear shaft bearings removal,齿轮轴轴承拆卸

5)tapered bore bearing removal,圆锥孔轴承拆卸

6)bearing puller assembly,轴承拆卸器总成

用法和例句

Upper Main Bearing Removal and Installation with Tool C-3059

用工具C-3059进行上主轴承拆卸与安装

If the axle shaft and hub bearing are being removed in order to service another component, the axle shaft and hub bearing can be removed as an assembly.

如果维修时需拆卸主动轴和轮毂轴承，主动轴和轮毂轴承可作为一个总成加以拆卸。

Remove side bearings from differential case.

拆卸差速箱处的侧轴承。

Replacing precision-insert main bearings without removing the crankshaft requires about 5 hours. Removing and replacing the crankshaft requires several additional hours.

不拆曲轴更换精密嵌入型主轴承,大约需要5小时,拆卸和更换轴承要额外增加几小时。

Remove differential case and dummy bearings from axle housing.

拆卸轴壳内的差速箱和平衡轴承。

"On many engines, the connection-rod and main bearings (crankshaft bearings) can be checked for wear with an oil-leak detector before the engine is torn down."

许多发动机在拆卸之前,可以用漏油检测装置检查连杆和主轴承(曲轴轴承)的磨损情况。

Remove differential side bearings from differential case.

从差速箱拆卸差速器侧轴承。

Remove thrust bearings from rear main bearing carrier.

从后主轴承托架上拆下止推轴承。

MAIN BEARING JOURNAL DIAMETER (CRANKSHAFT REMOVED)

主轴承颈部直径（曲轴已卸去）

Research on the Quick Non-damage Dismantling of Bearings by Making Use of Industrial Frequency Induction Heating;

工频感应加热快速无损拆卸轴承技术研究

It is not advisable to attempt to replace camshaft bearings unless special removal and installation tools are available.

不要试图更换凸轮轴轴承，除非能够使用特殊的拆卸和安装工具。

Remove the depth shims from rear pinion bearing cup bore in axle housinRecord the thickness of the depth shims.

从轴管里的后小齿轮轴承盖孔拆卸限深垫片。记录限深垫片厚度。

Remove differential case from axle housing.

从轴管上拆卸差速箱。

Development and ANSYS simulation of induction heating detacher for bearing inner race

轴承内环感应加热拆卸器的研制及其有限元仿真

Remove the crankshaft from the cylinder block (refer to Cylinder Block Disassemble).

从汽缸体上卸去曲轴（参看“汽缸体－拆卸”）。

Remove the lower insert from the bearing cap.

从轴承盖上拆去下轴瓦。

"When the crankshaft is removed, it is the usual procedure to clean out the oil passages in the crankshaft."

拆卸曲轴时,通常应该清洁曲轴油道。

Research on Disassembly and Recycling Technique for Spindle System of Numerical Control Lathe;

绿色数控车床主轴组件的可拆卸与可回收性技术研究